Exactly how to Replace a Tub (Step By Step).
Exactly how to Replace a Tub (Step By Step).
Blog Article
This article in the next paragraphs about How to Install a Bathtub Yourself is relatively remarkable. Check it out yourself and decide what you think about it.
Setting up a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult project. If the old tub is easily obtainable, the project can move rapidly; if you need to open up a wall surface to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified yourself for the task as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will help you install a new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to transform the arrangement of your previous water supply pipes.
Your tools and also product list should make up the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome due to the restricted accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wood boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has actually been made use of at least once as this will certainly settle it right into its last placement.
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a ton for spending some time to read our short article. Enjoyed our entry? Please share it. Let others discover it. Thanks a lot for your time. Don't forget to pay a visit to our blog back soon.
Visit Our Website Report this page